Fishing for bream from the boat

1

On large reservoirs large bream coming to the shore relatively rare. Usually this happens during hot and calm weather, evening and night. In all other cases, the bream prefers to stick with the watering, the edges of pits and ditches in lakes and reservoirs.

No matter how you know the place where the pit is located near the shore, and she has the ability to throw the bait by using a particular tackle, still fishing in such places is not always effective. This is due to the fact that anglers quickly detects such sections and try every day to catch some big fish, usually with bottom snap-ins. Massive pressure eventually leads to the fact that the big fish leave these places. Since the number of promising places for fishing from shore is limited, we have to look for the fish on the distance from the shore, and this is due to the use of the boats.

For a comfortable and most importantly safe fishing makes sense to get a stable and roomy boat with a motor, especially if the fishing is on a large river or a wide lake. The motor is needed in order to quickly get to your chosen space, quickly change the location if necessary, and also to just stand on the anchors in the selected location. The fact is that while fishing on the boat is very desirable to put in two anchors across the current, in the stretch, and it’s easy to do in the following way. At low speed the boat turns across the current and drop the bow anchor, after almost all the rope would be pulled astern, jamming the motor and drop the bow anchor. Then the boat is right across the flow. If you use a rowing boat, due to the demolition just stand in place is difficult, especially if the angler is alone, without partner.

Despite clear progress in fishing gear, everywhere you can find “old-fashioned” devices, however, is very effective. For fishing on the course, there are different tackle that depends on conditions of fishing, and from the local traditions and fashion trends.

If the depth does not exceed 5-6 meters, traditionally used in a classic wiring with the release of fishing line from the boat. Tackle is a clearomizer rod with a length of 4-7 meters, equipped with throughput rings, reel seat, reel with a supply of fishing line. If the depth of fishing does not exceed the length of the rod, then apply the snap-in with stationary floats, otherwise used moving floats. In fact, in both cases preferably floats with one attachment point of the line.

For successful fishing need to find or “table” or top edge of the channel. Once the boat anchored, lowered into the water the bait or in the form of spheres, or in a severe trough. The feeder is usually designed for five to six kilos of bait in the form of millet or other cereals. As baits use the same nozzles as for fishing from the shore, but still more often in the case are worm and maggot, and “sandwich” of them.

When fishing deep moving the snap-in is most effective on smooth and fairly low flow. If the current is strong and rough, the widely used so-called side rods.
Side rods can be divided into two constructs. The first option is a long winter for spinning and trolling in a plumb. Spinning can be equipped with a coil or reel, which anglers reel up the line quite thick, sometimes up to a diameter of 0.3 mm. At the end of the line tie or a hook or jig. Above the hook is a sinker, was often absent. The lure trying to find this size, so additional weights were not required. At the end of the spinning mounted long (up to half) of a pointer made of wire or steel plate. Tackle very rough, but if you know exactly where the Parking lot is big bream, his bite and know that bream are now well caught, the result can be quite impressive.

What’s wrong with such tackle: it is good to catch in a quiet, calm weather, when the river still is no heavy traffic. When on the river, the excitement, the lure is rigidly connected with the pointer, is in constant, chaotic motion, and it is large bream does not like. What can you advise, if you still catch in a fairly strong emotion. First, use a long hut of a flat steel spring. Second, to increase the distance between the hook and the sinker and a half to two meters. Thirdly, put on the line small (0.5 g) was at a distance of approximately 30-40 cm above the hook. But increasing the length of the leash, you will relate baits from bait, and this can dramatically reduce the number of bites, because the fish are concentrated directly on the bait.

If the depth of fishing is large, the current is rather strong, continuous turbulence on the water, it is better to use the tackle in which the feeder is combined with a sinker. There are two versions of the equipment. The classic version is that is used on the line, at the end of which is tied to two short (10-15 cm) leash. The sinker is a “eight” thick rod or metal casting. The inner diameter of the small ring of the group may be from one to five millimeters, and the diameter of the big ring a lot more. The circumference of the large ring has an angular slot as on the uncoupling. This slot introduced a strict fishing line or rope on the end of which is tied to the manger. On the line with a leash is attached to the stopper at a distance of about 30-50 cm from the hooks.

Fishing technique is very simple and effective. First, the bottom is lowered down on a rope feeder filled with groundbait. Then the rope from the feeder starts in the big ring and the group slowly lowered to the bottom. These apparatus are received at the time the name “koltsovka”.

I in the childhood quite a lot were caught using the gear and I can say that I did not like it. Why? There are two reasons. First, it seemed to me that the big fish still afraid of the feeders of large size may be due to the fact that they are very “whistle” on a powerful current. Secondly, if the tide is changing in the process of fishing, and this is typical for all regulated dams and rivers, that at some point in time, the weight of the koltsovki becomes optimal, which leads to frequent entanglement of fishing line with hooks for the rope, which is tied to the manger. Very often bream gets second leash on the rope, or touches them to the trough. To prevent tangling of the gear necessary to increase the length of leads and thereby reduce the efficiency of fishing.
A much more effective tackle “spring”. It represents a rigid rod of length 1.5-1.7 m, is equipped with a powerful coil, which stores a supply of fishing line to 0.3 mm wire in diameter of 0,15 mm.

A strong current in a thin wire is much smaller parasit through it as through a wicker, perfectly transmitted the slightest bite. However, the use of wire due to the fact that you need to treat your gear. Appearance on the wire gizmo-twisting” causes the rope to lose wire in this place is broken. Thick fishing line has its advantages. Remove heavy tackle with great depth still faster hands, and thick lines little confused. At the end of the fishing line tied two short leash. Above them at a distance of 10 cm is mounted the swivel retainer from above the retainer is the spring. Spring is a twisted steel wire (1-1. 5 mm) with a diameter of 3.5-5 cm and a length of 15 cm to Both end of the spring is filled with lead, through which the axis of the spring is passed a copper tube with a diameter of 2-3 mm. At one end of the tube sealed “tightly”, and the second end is not. This is necessary in order to stuffed with groundbait feeder was in the stretched condition. The weight of the spring without the mixture reaches 250 g as bait used millet, barley or buckwheat, and as bait works best worm.

LEAVE A REPLY

Please enter your comment!
Please enter your name here